Prusa i3 - Cura Config DEFAUT | Prusa i3 - Cura Config Preset |
[profile] layer_height = 0.1 wall_thickness = 0.8 retraction_enable = True solid_layer_thickness = 0.6 fill_density = 20 nozzle_size = 0.5 print_speed = 50 print_temperature = 220 print_temperature2 = 0 print_temperature3 = 0 print_temperature4 = 0 print_bed_temperature = 70 support = None platform_adhesion = None support_dual_extrusion = Both wipe_tower = False wipe_tower_volume = 15 ooze_shield = False filament_diameter = 2.85 filament_diameter2 = 0 filament_diameter3 = 0 filament_diameter4 = 0 filament_flow = 100.0 retraction_speed = 40.0 retraction_amount = 4.5 retraction_dual_amount = 16.5 retraction_min_travel = 1.5 retraction_combing = True retraction_minimal_extrusion = 0.02 retraction_hop = 0.0 bottom_thickness = 0.3 layer0_width_factor = 100 object_sink = 0.0 overlap_dual = 0.15 travel_speed = 150.0 bottom_layer_speed = 20 infill_speed = 0.0 inset0_speed = 0.0 insetx_speed = 0.0 cool_min_layer_time = 5 fan_enabled = True skirt_line_count = 1 skirt_gap = 3.0 skirt_minimal_length = 150.0 fan_full_height = 0.5 fan_speed = 100 fan_speed_max = 100 cool_min_feedrate = 10 cool_head_lift = False solid_top = True solid_bottom = True fill_overlap = 15 support_type = Grid support_angle = 60 support_fill_rate = 15 support_xy_distance = 0.7 support_z_distance = 0.15 spiralize = False simple_mode = False brim_line_count = 20 raft_margin = 5.0 raft_line_spacing = 3.0 raft_base_thickness = 0.3 raft_base_linewidth = 1.0 raft_interface_thickness = 0.27 raft_interface_linewidth = 0.4 raft_airgap = 0.22 raft_surface_layers = 2 fix_horrible_union_all_type_a = True fix_horrible_union_all_type_b = False fix_horrible_use_open_bits = False fix_horrible_extensive_stitching = False plugin_config = object_center_x = -1 object_center_y = -1 [alterations] start.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm G92 E0 ;zero the extruded length G1 F200 E3 ;extrude 3mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} M117 Printing... end.gcode = ;End GCode M104 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning start2.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T1 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} M117 Printing... end2.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning start3.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T2 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end3.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M104 T2 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} start4.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T3 ;Switch to the 4th extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T2 ;Switch to the 3th extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T1 ;Switch to the 2nd extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 ;Switch to the first extruder G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end4.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M104 T2 S0 ;extruder heater off M104 T3 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning ;{profile_string} support_start.gcode = support_end.gcode = cool_start.gcode = cool_end.gcode = replace.csv = preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. ;This code is added before the T(n) postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. ;This code is added after the T(n) | [profile] layer_height = 0.2 wall_thickness = 1 retraction_enable = True solid_layer_thickness = 0.9 fill_density = 20 nozzle_size = 0.4 print_speed = 70 print_temperature = 220 print_temperature2 = 0 print_temperature3 = 0 print_temperature4 = 0 print_bed_temperature = 90 support = None platform_adhesion = Brim support_dual_extrusion = False filament_diameter = 2.85 filament_diameter2 = 0 filament_diameter3 = 0 filament_diameter4 = 0 filament_flow = 100 retraction_speed = 30 retraction_amount = 4.5 retraction_dual_amount = 16.5 bottom_thickness = 0.3 object_sink = 0.0 overlap_dual = 0.2 travel_speed = 150 bottom_layer_speed = 20 infill_speed = 100 cool_min_layer_time = 5 fan_enabled = True skirt_line_count = 1 skirt_gap = 3.0 fan_layer = 1 fan_speed = 100 fan_speed_max = 100 cool_min_feedrate = 10 cool_head_lift = False solid_top = True solid_bottom = True fill_overlap = 15 support_rate = 75 brim_line_count = 15 raft_margin = 5 raft_line_spacing = 1.0 raft_base_thickness = 0.3 raft_base_linewidth = 0.7 raft_interface_thickness = 0.2 raft_interface_linewidth = 0.2 fix_horrible_union_all_type_a = False fix_horrible_union_all_type_b = False fix_horrible_use_open_bits = False fix_horrible_extensive_stitching = False plugin_config = (lp1 . object_center_x = -1 object_center_y = -1 [alterations] start.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm G92 E0 ;zero the extruded length G1 F200 E3 ;extrude 3mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} M117 Printing... end.gcode = ;End GCode M104 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning start2.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T1 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} M117 Printing... end2.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning support_start.gcode = support_end.gcode = cool_start.gcode = cool_end.gcode = replace.csv = nextobject.gcode = ;Move to next object on the platform. clear_z is the minimal z height we need to make sure we do not hit any objects. G92 E0 G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 F{travel_speed} ;move Z up a bit and retract filament even more G90 ;absolute positioning G1 Z{clear_z} F{max_z_speed} G92 E0 G1 X{object_center_x} Y{object_center_y} F{travel_speed} G1 F200 E6 G92 E0 switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. G92 E0 G1 E-36 F5000 G92 E0 T{extruder} G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed} G1 E36 F5000 G92 E0 |
Prusa i3 - Cura Config DEFAUT Prusa i3 - Cura Config Preset
[profile]
layer_height = 0.1
wall_thickness = 0.8
retraction_enable = True
solid_layer_thickness = 0.6
fill_density = 20
nozzle_size = 0.5
print_speed = 50
print_temperature = 220
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
print_bed_temperature = 70
support = None
platform_adhesion = None
support_dual_extrusion = Both
wipe_tower = False
wipe_tower_volume = 15
ooze_shield = False
filament_diameter = 2.85
filament_diameter2 = 0
filament_diameter3 = 0
filament_diameter4 = 0
filament_flow = 100.0
retraction_speed = 40.0
retraction_amount = 4.5
retraction_dual_amount = 16.5
retraction_min_travel = 1.5
retraction_combing = True
retraction_minimal_extrusion = 0.02
retraction_hop = 0.0
bottom_thickness = 0.3
layer0_width_factor = 100
object_sink = 0.0
overlap_dual = 0.15
travel_speed = 150.0
bottom_layer_speed = 20
infill_speed = 0.0
inset0_speed = 0.0
insetx_speed = 0.0
cool_min_layer_time = 5
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 150.0
fan_full_height = 0.5
fan_speed = 100
fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
solid_bottom = True
fill_overlap = 15
support_type = Grid
support_angle = 60
support_fill_rate = 15
support_xy_distance = 0.7
support_z_distance = 0.15
spiralize = False
simple_mode = False
brim_line_count = 20
raft_margin = 5.0
raft_line_spacing = 3.0
raft_base_thickness = 0.3
raft_base_linewidth = 1.0
raft_interface_thickness = 0.27
raft_interface_linewidth = 0.4
raft_airgap = 0.22
raft_surface_layers = 2
fix_horrible_union_all_type_a = True
fix_horrible_union_all_type_b = False
fix_horrible_use_open_bits = False
fix_horrible_extensive_stitching = False
plugin_config =
object_center_x = -1
object_center_y = -1
[alterations]
start.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
M117 Printing...
end.gcode = ;End GCode
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
T1
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F200 E-{retraction_dual_amount}
T0
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
M117 Printing...
end2.gcode = ;End GCode
M104 T0 S0 ;extruder heater off
M104 T1 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
start3.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M104 S{print_temperature} ;Uncomment to add your own temperature line
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
T2 ;Switch to the 2nd extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F200 E-{retraction_dual_amount}
T1 ;Switch to the 2nd extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F200 E-{retraction_dual_amount}
T0 ;Switch to the first extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
;Put printing message on LCD screen
M117 Printing...
end3.gcode = ;End GCode
M104 T0 S0 ;extruder heater off
M104 T1 S0 ;extruder heater off
M104 T2 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
;{profile_string}
start4.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M104 S{print_temperature} ;Uncomment to add your own temperature line
;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
T3 ;Switch to the 4th extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F200 E-{retraction_dual_amount}
T2 ;Switch to the 3th extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F200 E-{retraction_dual_amount}
T1 ;Switch to the 2nd extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F200 E-{retraction_dual_amount}
T0 ;Switch to the first extruder
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
;Put printing message on LCD screen
M117 Printing...
end4.gcode = ;End GCode
M104 T0 S0 ;extruder heater off
M104 T1 S0 ;extruder heater off
M104 T2 S0 ;extruder heater off
M104 T3 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
;{profile_string}
support_start.gcode =
support_end.gcode =
cool_start.gcode =
cool_end.gcode =
replace.csv =
preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
;This code is added before the T(n)
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
;This code is added after the T(n)
Imprimir a primeira camada com menos velocidade e com uma camada mais grossa de filamento também ajuda
Ate porque ha peças que não dão para imprimir com draft!
Por exemplo já me pediram "protótipos" de porta chaves...
Imprimires aquilo com raft é das piores coisas... Que podes fazer.
Eu é PLA. Compro na BQ.
Experimentei o branco da Bee e entupiu me o extrair. Tive mesmo de o desmontar para desentupir aquilo à força.
ABS nunca usei. Tens preferência por esse porquê?
Pessoas das impressoras 3d, por acaso o PLA é resistente a solventes, mais especificamente gasolina?
O ABS dado que se desfaz com diluente ou acetona deve sofrer da mesma doença com gasolina, será que o PLA se aguenta?
Mas tambem fica maleavel a uns 80º e deforma-se, provavelmente a melhor ideia será maquinar as peças usando nylon ou algo do género ::)
Bem podiamos abrir ai uma secção para impressão 3D.
Estou com um problema, surgiu sem razao aparente e os drives estao calibrados segundo as tensões sugeridas pela BQ.
Mas os motores, naoe stao a funcionar correctamente, as vezes dão solavancos, e depois ficam a com um ruido tipo como que estivesse a querer dar outro passo mas volta a traz...
No video se tiverem atenção ao som dá para perceber.
https://www.youtube.com/watch?v=2vVHxGT3LkQ (https://www.youtube.com/watch?v=2vVHxGT3LkQ)
Dado que tens mais drivers e motores iguais, troca os fios desse motor com um motor da mesa, ficas logo a saber de onde é a doença.Boa sugestão, contudo vou ter de ver bem isso porque os motores acho que não são iguais (os drivers sim).
Que tensões recomendadas são essas e onde são aplicadas?Estão mencionadas nesse pdf. PDF (https://static-bqreaders.s3.amazonaws.com/file/Prusa/7_Prusa_QSG_Calibração_pt.pdf)
Estás a falar de um potenciometro chamado para ai Vref ou Iref que é usado para o valor de chopping da corrente.
Ou o driver diz 24v e estás-lh e a dar com mais?
This XML file does not appear to have any style information associated with it. The document tree is shown below.
<Error>
<Code>AccessDenied</Code>
<Message>Access Denied</Message>
<RequestId>3E928F9FB8AB2934</RequestId>
<HostId>
yAaXE716RnSPj6uN7PRPAB4djVWrd2jLwBYhjl8Ysv5FKM1Z1ymG+nZWrWqZZORJhlamajPViJE=
</HostId>
</Error>
Linux no liky liky that link ::)CitarThis XML file does not appear to have any style information associated with it. The document tree is shown below.
<Error>
<Code>AccessDenied</Code>
<Message>Access Denied</Message>
<RequestId>3E928F9FB8AB2934</RequestId>
<HostId>
yAaXE716RnSPj6uN7PRPAB4djVWrd2jLwBYhjl8Ysv5FKM1Z1ymG+nZWrWqZZORJhlamajPViJE=
</HostId>
</Error>
Peço desculpa por "desenterrar" este tópico.
Comprei esta impressora da bq e já está montada, mas tenho tido dificuldades pois apesar de já ter feito a calibração da mesa várias vezes, o plástico não agarra bem na mesa logo na 1ª camada ou após 2, 3 camadas começa a soltar-se.
Penso que a distância do extrusor à mesa já seja a correcta, já tentei com laca, com fita de pintor e até com uma folha de papel...
Alguma alma caridosa me pode dar uma dica sobre o que estará mal?
Agradeço antecipadamente
Aqui vão os meus settings para o Cura:
Layer Height: 0.2
Shell Thickness: 1.2
Enable Retraction: Yes
Bottom/Top Thickness: 1
Fill Density: 20
Print Speed: 60
Print Temperature: 215
Support Type: Touching Buildplate
Plataform Adhesion Type: Raft
Diameter: 1.75
Flow: 100
I've bought and assembled one of your Hephestos.e recebi a seguinte resposta:
It came with firmware 1.3.1, i've read there are some advantages in upgrading to a
newer version.
I'd like to know if all i have to do is upgrade with the arduino software or do i
have to tweak some settings and calibrate the motor drivers again?
Thanks in advance,
Pedro
Very Good Morning Mr. Oliveira,
Thank you for contacting BQ technical support department.
To upgrade the Hephestos firmware, we recommend you to download the firmwares with the following link:
http://storage.googleapis.com/impresoras/FW-v1.4.2/Hephestos/FW-v1.4.2-Hephestos-Marlin_hephestos.zip (http://storage.googleapis.com/impresoras/FW-v1.4.2/Hephestos/FW-v1.4.2-Hephestos-Marlin_hephestos.zip)
Besides, enclosed I ease you a User Guide to upgrade the printer with Cura software.
Best regards,
Má calibração dos passos por mm no firmwareoi ?
Boas, ja tenho a bq prusa I3 á algum tempo e tenho usado o software cura, mas quero fazer uma impressão, imaginem um cubo com 2mm de parede mas num dos lados não esta a fazer a parede direita, imprime o lado de fora e o preenchimento interno mas a parede de dentro não esta a imprimir, nao encontra nada de mal no desenho. por esse motivo comecei a experimentar o slic3r, mas as impressões saem uma valente bosta :) de certeza que são as configurações, alguém me pode ajudar a configurar aquilo para esta impressora?
Boas, ja tenho a bq prusa I3 á algum tempo e tenho usado o software cura, mas quero fazer uma impressão, imaginem um cubo com 2mm de parede mas num dos lados não esta a fazer a parede direita, imprime o lado de fora e o preenchimento interno mas a parede de dentro não esta a imprimir, nao encontra nada de mal no desenho. por esse motivo comecei a experimentar o slic3r, mas as impressões saem uma valente bosta :) de certeza que são as configurações, alguém me pode ajudar a configurar aquilo para esta impressora?
A quanto tens o fill density?
a 20%
á algum sitio onde possa ver as configurações todas para esta impressora?
Eu tenho no mínimo a 30%.Boas, ja tenho a bq prusa I3 á algum tempo e tenho usado o software cura, mas quero fazer uma impressão, imaginem um cubo com 2mm de parede mas num dos lados não esta a fazer a parede direita, imprime o lado de fora e o preenchimento interno mas a parede de dentro não esta a imprimir, nao encontra nada de mal no desenho. por esse motivo comecei a experimentar o slic3r, mas as impressões saem uma valente bosta :) de certeza que são as configurações, alguém me pode ajudar a configurar aquilo para esta impressora?
A quanto tens o fill density?
a 20%
á algum sitio onde possa ver as configurações todas para esta impressora?
@Kristey - o extrusor é todo de metal? Pode ser duas coisas, maus acabamentos ou ma qualidade de plaO extrusor é todo em metal. É o novo extrusor da BQ. E não me deu problemas ate agora, Tal como o primeiro que tive e que eles trocaram. Não me deram problemas e quando começaram a dar era em todas as impressões. Desentupo e cega a meia da impressão começa a imprimir tudo mal.
Se for todo de metal podes tentar duas coisas, uma técnica chamada seasoning, que consiste em molhar ai 1cm do filamento em óleo vegetal, com o hotend na temperatura aconselhada vais forçando o filamento até deixar de deitar fumo, basicamente estas a fazer o mesmo que fazes com os ovos na frigideira, o pla é um açúcar (feito de milho) e agarra ao inox.Isso explica o cheiro a caramelo.
Outra coisa que podes tentar é polir o interior do tubo com areia fina e uma broca do mesmo diâmetro, agarras o tubo com um alicate e colocas uma ponta dentro da areia, inseres a broca e com o berbequim em altas rotações começas a puxar areia para dentro do tubo durante uns segundos, a areia fina vai-se desfazer e polir o tubo, cuidado que fazer isto desta forma pode ser perigoso, podes tambem tentar arranjar uma broca própria para polir, mas são caríssimasNão percebi bem a tecnica, mas estou interessado. Podes explicar melhor?
mas nao tem a ver com isso, essa percentagem é a de preenchimento interior, no caso o que me acontece é que o extruder deixa montes de plastico e nao desenha com precisão nenhumaIsso deverá ser problema do PLA, já vi PLA com características completamente diferentes na qualidade das peças.