LusoRobótica - Robótica em Português
Sistemas específicos => Arduino / AVR => Tópico iniciado por: magtaem em 21 de Junho de 2014, 15:50
-
Boas pessoal tenho uma dúvida referente a este sensor, fiz a ligação deste sensor como mostra a seguinte imagem
(https://lusorobotica.com/proxy.php?request=http%3A%2F%2Fi01.i.aliimg.com%2Fimg%2Fpb%2F676%2F851%2F568%2F568851676_298.jpg&hash=6b11252d1a1f717e5f0b1094454beb46688db180)
VCC -5v
DATA - Pino 2
GND - GND
NO arduino coloquei o seguinte código:
#include <OneWire.h>
int DS18S20_Pin = 2; //DS18S20 Signal pin on digital 2
//Temperature chip i/o
OneWire ds(DS18S20_Pin); // on digital pin 2
void setup(void) {
Serial.begin(9600);
}
void loop(void) {
float temperature = getTemp();
Serial.println(temperature);
delay(100); //just here to slow down the output so it is easier to read
}
float getTemp(){
//returns the temperature from one DS18S20 in DEG Celsius
byte data[12];
byte addr[8];
// if ( !ds.search(addr)) {
//no more sensors on chain, reset search
// ds.reset_search();
// return -1000;
// }
//if ( OneWire::crc8( addr, 7) != addr[7]) {
// Serial.println("CRC is not valid!");
// return -1000;
// }
// if ( addr[0] != 0x10 && addr[0] != 0x28) {
// Serial.print("Device is not recognized");
// return -1000;
// }
ds.reset();
ds.select(addr);
ds.write(0x44,1); // start conversion, with parasite power on at the end
byte present = ds.reset();
ds.select(addr);
ds.write(0xBE); // Read Scratchpad
for (int i = 0; i < 9; i++) { // we need 9 bytes
data[i] = ds.read();
}
ds.reset_search();
byte MSB = data[1];
byte LSB = data[0];
float tempRead = ((MSB << 8) | LSB); //using two's compliment
float TemperatureSum = tempRead / 16;
return TemperatureSum;
}
Mas o sensor retorna sempre 0.00 , não dá valores, o que estou a fazer de mal?
Nota : Já importei a library onewire
Cumprimentos
-
Começa por tirar os comentários da parte em que diz se está a identificar o sensor ou não.
Tens resistência de pull-up de 10k na linha de dados?
-
Começa por tirar os comentários da parte em que diz se está a identificar o sensor ou não.
Tens resistência de pull-up de 10k na linha de dados?
SIm tenho a resistência, e se tirar essa parte dos comentários, ele dá o valor -1.
Eu só tirei para testar uma pequena coisa
-
Tenta usar uma biblioteca já feita, porque estás ai a chamar um addr, e não estou a entender de onde é que esse endereço vem.
Aliás, provavelmente o problema é mesmo esse, primeiro tens de fazer um scan á linha one wire para saber quem é que lá está, guardar os endereços num array e só depois é que lês sensor a sensor, dando o endereço dele.
-
Ou seja, vou roubar o código a outro lado certo?
Desde já obrigado pela ajuda
-
Código correcto :
#include <OneWire.h>
// OneWire DS18S20, DS18B20, DS1822 Temperature Example
//
// http://www.pjrc.com/teensy/td_libs_OneWire.html
//
// The DallasTemperature library can do all this work for you!
// http://milesburton.com/Dallas_Temperature_Control_Library
OneWire ds(2); // on pin 10 (a 4.7K resistor is necessary)
void setup(void) {
Serial.begin(9600);
}
void loop(void) {
byte i;
byte present = 0;
byte type_s;
byte data[12];
byte addr[8];
float celsius, fahrenheit;
if ( !ds.search(addr)) {
Serial.println("No more addresses.");
Serial.println();
ds.reset_search();
delay(250);
return;
}
Serial.print("ROM =");
for( i = 0; i < 8; i++) {
Serial.write(' ');
Serial.print(addr[i], HEX);
}
if (OneWire::crc8(addr, 7) != addr[7]) {
Serial.println("CRC is not valid!");
return;
}
Serial.println();
// the first ROM byte indicates which chip
switch (addr[0]) {
case 0x10:
Serial.println(" Chip = DS18S20"); // or old DS1820
type_s = 1;
break;
case 0x28:
Serial.println(" Chip = DS18B20");
type_s = 0;
break;
case 0x22:
Serial.println(" Chip = DS1822");
type_s = 0;
break;
default:
Serial.println("Device is not a DS18x20 family device.");
return;
}
ds.reset();
ds.select(addr);
ds.write(0x44); // start conversion, use ds.write(0x44,1) with parasite power on at the end
delay(1000); // maybe 750ms is enough, maybe not
// we might do a ds.depower() here, but the reset will take care of it.
present = ds.reset();
ds.select(addr);
ds.write(0xBE); // Read Scratchpad
Serial.print(" Data = ");
Serial.print(present, HEX);
Serial.print(" ");
for ( i = 0; i < 9; i++) { // we need 9 bytes
data[i] = ds.read();
Serial.print(data[i], HEX);
Serial.print(" ");
}
Serial.print(" CRC=");
Serial.print(OneWire::crc8(data, 8), HEX);
Serial.println();
// Convert the data to actual temperature
// because the result is a 16 bit signed integer, it should
// be stored to an "int16_t" type, which is always 16 bits
// even when compiled on a 32 bit processor.
int16_t raw = (data[1] << 8) | data[0];
if (type_s) {
raw = raw << 3; // 9 bit resolution default
if (data[7] == 0x10) {
// "count remain" gives full 12 bit resolution
raw = (raw & 0xFFF0) + 12 - data[6];
}
} else {
byte cfg = (data[4] & 0x60);
// at lower res, the low bits are undefined, so let's zero them
if (cfg == 0x00) raw = raw & ~7; // 9 bit resolution, 93.75 ms
else if (cfg == 0x20) raw = raw & ~3; // 10 bit res, 187.5 ms
else if (cfg == 0x40) raw = raw & ~1; // 11 bit res, 375 ms
//// default is 12 bit resolution, 750 ms conversion time
}
celsius = (float)raw / 16.0;
fahrenheit = celsius * 1.8 + 32.0;
Serial.print(" Temperature = ");
Serial.print(celsius);
Serial.print(" Celsius, ");
Serial.print(fahrenheit);
Serial.println(" Fahrenheit");
}
Cumprimentos e obrigado