Parece estar com obrilhocontraste no máximo, existe um trimmer de ajuste na placa que se liga ao display.
Primeiro convinha apresentaste na secção correcta, pois é obrigatório, e depois é que colocas as duvidas, o mais detalhado possível.
Dando um tiro no escuro, está a usar a biblioteca propria para o uso do lcd por 2 fios? Ou estas a usar a que vem predefinida no software arduino.
/*
LiquidCrystal Library - Hello World
Demonstrates the use a 16x2 LCD display. The LiquidCrystal
library works with all LCD displays that are compatible with the
Hitachi HD44780 driver. There are many of them out there, and you
can usually tell them by the 16-pin interface.
This sketch prints "Hello World!" to the LCD
and shows the time.
The circuit:
* LCD RS pin to digital pin 12
* LCD Enable pin to digital pin 11
* LCD D4 pin to digital pin 5
* LCD D5 pin to digital pin 4
* LCD D6 pin to digital pin 3
* LCD D7 pin to digital pin 2
* LCD R/W pin to ground
* 10K resistor:
* ends to +5V and ground
* wiper to LCD VO pin (pin 3)
Library originally added 18 Apr 2008
by David A. Mellis
library modified 5 Jul 2009
by Limor Fried (http://www.ladyada.net)
example added 9 Jul 2009
by Tom Igoe
modified 22 Nov 2010
by Tom Igoe
This example code is in the public domain.
http://www.arduino.cc/en/Tutorial/LiquidCrystal
*/
// include the library code:
#include <LiquidCrystal.h>
// initialize the library with the numbers of the interface pins
LiquidCrystal lcd(12, 11, 5, 4, 3, 2);
void setup() {
// set up the LCD's number of columns and rows:
lcd.begin(20, 4);
// Print a message to the LCD.
lcd.print("hello, world!");
}
void loop() {
// set the cursor to column 0, line 1
// (note: line 1 is the second row, since counting begins with 0):
lcd.setCursor(0, 1);
// print the number of seconds since reset:
lcd.print(millis()/1000);
}
Tens o teu LCD ligado por I2C, e esse código é para ligação direta arduino-LCD.
Basta ler os comentários do código.
Dá-me tanto trabalho encontrar o código na net como a ti, e hoje já estou ocupado que chegue...
Usa código para um lcd i2c, quase de certeza que onde o compraste que terá lá uns links ou umas sugestões.
//YWROBOT
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,20,4); // set the LCD address to 0x27 for a 16 chars and 2 line display
void setup()
{
lcd.init(); // initialize the lcd
lcd.init();
// Print a message to the LCD.
lcd.backlight();
lcd.setCursor(3,0);
lcd.print("Hello, world!");
lcd.setCursor(2,1);
lcd.print("SainSmart for UNO");
lcd.setCursor(2,2);
lcd.print("SainSmart LCM IIC");
lcd.setCursor(1,3);
lcd.print("Design By SainSmart");
}
void loop()
{
}
HelloWorld:5: error: 'LiquidCrystal_I2C' does not name a type
HelloWorld.pde: In function 'void setup()':
HelloWorld:9: error: 'lcd' was not declared in this scope
Essa Board Module Port IIC/I2C/TWI/SP??I Serial Interface é apenas para LCD 16x2?
Board Module Port IIC/I2C/TWI/SP??I Serial Interface pode ser para qualquer lcd ou tem que ser para uma propria, exemplo, 16x2 nao da certo em 20x4?